Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
We've unearthed the article about Installing A Bathtub directly below on the net and reckoned it made good sense to talk about it with you on this page.
Mounting a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily obtainable, the job can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. Instead of employing a professional to take over a halfway-completed task, it is much better to consider using one before you start. Opportunities are you may require an expert plumber to make tube links.
This post will help you mount a new bath tub in your washroom if you have currently gotten a new tub as well as do not require to change the plan of your previous water system pipes.
Your tools and also material list must make up the following:
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing faucets can be quite problematic due to the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. Once the supply pipes have actually been removed, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the tub in the required position. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, fix the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be linked to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is suggested to fit the tiles making use of waterproof or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub Yourself? Place feedback further down. We'd be pleased to see your feelings about this write-up. Hoping that you come back again soon. So long as you enjoyed reading our blog posting please remember to pass it around. Bless you for your time. Please check our website back soon.
Need help? Call. Report this page